Stay the course when putting new shingles in place

HOME WORK

July 02, 1994|By Karol V. Menzie and Randy Johnson

Once you accept the fact that it's going to be hard labor, reshingling a roof isn't difficult. It's not, as a woodworking friend of ours likes to say, brain surgery -- though it's not for the brain-dead either, as you need to keep your wits about you while you're working on a slanted surface so far above the ground.

If you went up to measure the roof to find out how many shingles to order (three bundles per hundred square feet), the terrain shouldn't be completely unfamiliar. Remember to order an extra 10 percent to 20 percent for waste and miscalculation. If you can get the bundles easily, go for the lower figure; if the shingles have to be delivered from some distant warehouse, add the higher percentage to avoid frustration. Check to see if you can return unopened bundles.

Check also to see if the supplier has a conveyor-belt delivery system; it's a truck- or trailer-mounted conveyor that can deliver the shingles right to the roof. Having the shingles delivered to the roof is worth paying a few extra dollars. The alternative is carrying dozens of bundles of shingles, each weighing 80 to 100 pounds, to the roof on your shoulder, one bundle at a time.

Wherever your shingles end up, keep them dry by covering them with a tarp or heavy plastic. If the paper wrapping gets soggy, the bundles could fall apart -- a real pain.

Roofing doesn't require a wide variety of tools. You'll need a hammer, a utility knife with lots of extra blades, a tape measure, a carpenter's square, and roofing nails. To install new shingles over old, use roofing nails long enough to go through all layers and into the underlying surface at least 3/4 of an inch. Order plenty of nails -- they're available in 50-pound boxes -- because you really don't want to run out. Each shingle takes four nails, and there are 27 shingles in a bundle.

You also need roofing cement, and a caulk gun with silicone caulk. Tin snips, for cutting flashing and trimming shingles, are

also useful.

Check the flashing

Before you start on the shingles, however, you need to go up on the roof and check out the flashing -- the metal strips that line valleys, and go around anything that protrudes through the roof, like chimney and pipes. There may also be some flashing on the edge of the roof. If it's in good shape, all you have to do is nail down any loose spots. If it's damaged or worn, however, you'll have to replace it. (If the roof is simple, a two-sided peak, for instance, with one chimney protruding, you can probably replace the flashing yourself. If the roof has a lot of peaks and valleys, however, you may want to get professional help with the flashing.)

Once the prep work is done, you're ready to start nailing. Here are the steps.

*First, familiarize yourself with the parts of a shingle. We're assuming you're using a standard three-tab asphalt or fiberglass shingle, 12 inches high by 36 inches wide. The tabs, the bottom part of the shingle, are the part that shows, the part that has the color you have chosen. The top part is usually black with a row of self-sealing adhesive where the nails will be driven in. Read the wrapper carefully; it should tell you how to cut them and suggest a nailing pattern.

*Roofing goes on in rows, called courses, starting along the bottom edge and ending at the ridge. The first strip of shingling, the starter strip, has no tabs. It's a piece trimmed from the black part of the shingle that butts against the bottom of the original second course, providing a flat surface for the new first course. Trim several inches off one end of the first strip so old seams will be covered. Nail every 2 or 3 inches.

*Once the entire row of starter strips is in place, start on the first course. This course usually starts with a full shingle. It should butt against the bottom of the old third course, with the ends of the tabs even with the bottom of the starter strips. You may have to trim it an inch or so to make it fit -- trim the black part, not the tabs. Put nails 1 inch from each side in the adhesive, and above each tab cutout (the slot that forms the tab). It's important to stick to this nailing scheme so nails will always be covered.

*The first shingle is always trimmed, to make the cutouts stagger. It should say on the wrapper how much to cut off. Always cut from the same side and always start each course at the same edge of the roof. The cut edge of a shingle should always be on the outside edge of the roof.

Baltimore Sun Articles
|
|
|
Please note the green-lined linked article text has been applied commercially without any involvement from our newsroom editors, reporters or any other editorial staff.